We've noticed this article on Tools You Need to Install a New Bathtub down the page on the web and think it made perfect sense to relate it with you over here.
Mounting a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Changing an old bath tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the project can move quickly; if you have to open up a wall surface to get rid of the old bathtub and also position the new bathtub, the task is much harder. In either situation, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Chances are you may need a professional plumber to make tube connections.
This article will help you mount a brand-new bath tub in your washroom if you have actually currently gotten a brand-new bathtub as well as don't need to change the setup of your previous water system pipes.
Your tools and material list need to consist of the following:
Planning for the Installment
Firstly, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the maker's directions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets device to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its last setting.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the restricted accessibility that is typically the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. When the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub until the spirit level checks out degree.
To mount taps, fit the bottom of the outermost adaptable faucet connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water system and also examine all joints and new pipework for leaks as well as tighten them if needed. Load the bathtub and also inspect the overflow electrical outlet as well as the regular electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub needs to wait until the bathtub has been used at least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in place in between the faucet and also the sink. Protect the tap in place with the producer provided backnut. Once the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous kind ought to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to permeate the wall in between the bathroom as well as the tiling, leading to difficulties with moisture and feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealant can split fairly very early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is suggested to fit the tiles making use of water-resistant or water-proof adhesive as well as grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
Hopefully you enjoyed reading our section about How to Install a Bathtub. Many thanks for spending some time to read through our article. Don't hesitate to take the time to promote this article if you appreciated it. We cherish reading our article about How to Install a Bathtub.
Top Article